| Customization: | Available |
|---|---|
| Heating Mode: | Dielectric |
| Material Status: | Powder, Solution |
Suppliers with verified business licenses
Audited Supplier Audited by an independent third-party inspection agency
Miniature laboratory automatic or manual spray dryer with low noise and excellent drying effect
Introduction of spray dryer:
The YM-015 mini laboratory spray dryer (small spray dryer) has a compact design and can be placed independently in the laboratory or placed on a specially designed stainless steel rack. It is self-contained and can be operated without other facilities. One-button start-up, large color LCD touch screen operation, two operating modes, fully automatic or manual monitoring, can be used to facilitate operation and monitoring of experimental process. It is currently a spray dryer with the smallest volume, minimum noise, and excellent drying effect.
2. Equipment advantages:
Original imported nozzle, high efficiency.
Color LCD touch screen parameter display: air inlet temperature / air outlet temperature / peristaltic pump speed / air volume / needle frequency.
Fully automatic control: one-button start-up, after setting the spraying process parameters, the temperature reaches the predetermined temperature, the peristaltic pump starts, the running animation is displayed on the touch screen, and the running process is clearly displayed; just press the stop button when shutting down, the machine will automatically shut down safely.
Manual control: If you need to adjust the process parameters during the experiment, you can easily switch to the manual state, and the color touch screen dynamic display (animation) throughout the experiment
Equipped with nozzle cleaner, when the nozzle is blocked, it will be automatically cleared, and the frequency of the needle can be adjusted automatically.
Shutdown protection function: just press the stop button when shutting down, the machine will stop running immediately except for the fan, to ensure that the equipment will not burn out due to misoperation (forced shutdown of the fan).
The spraying, drying and collecting system are made of transparent high-quality borosilicate heat-resistant glass materials, so that the drying process can be carried out in a non-polluting environment.
Built-in imported oil-free air compressor, the particle diameter of the powder spray is normally distributed, the fluidity is very good, the noise is very low, less than 60db.
The atomization structure of the two-fluid spray, the whole machine is made of high-quality stainless steel material, compact design, no auxiliary equipment.
The design of drying temperature control adopts real-time control PID constant temperature control technology, so that the temperature control in the whole temperature zone is accurate, and the heating temperature control accuracy is ±1ºC.
In order to keep the sample pure, equipped with air inlet filter.
The feed volume can be adjusted by the feed peristaltic pump, and the small sample volume can reach 50ml.
The particle size of the finished dry powder after drying is relatively uniform, and more than 95% of the dry powder is in the same particle size range.
For the sticky materials, there is a nozzle cleaner needle), which will be automatically cleared when the nozzle is blocked, and the frequency of the needle can be adjusted automatically.
Innovative tower wall purge device, higher material recovery rate.
Special protection function, the fan does not start, the heating cannot be started, and the air volume of the fan is adjustable.
Technical parameters of spray dryer:
|
Inlet air temperature control |
30 ºC ~ 300ºC |
|
Outlet air temperature control |
30 ºC~140ºC |
|
Evaporated water |
200mL/H ~ 1500ml/h |
|
Maximum feed volume |
1500ml/h (adjustable) |
|
Feeding method |
peristaltic pump adjustment, feeding amount: 30-1500ml/h |
|
Minimum feed volume |
50mL |
|
Temperature control accuracy |
±1ºC, adopt imported temperature control system |
|
Average drying time |
1.0~1.5S |
|
Dry air flux |
air volume 0-330m3/h wind pressure 686Pa |
|
Compressor |
Imported oil-free air compressor with good fluidity and very low noise. 0.55KW, gas production 4.2m3/h, working pressure 2-5bar |
|
Jet device (Nozzle Cleaner) |
variable firing pin frequency (built-in 2.3bar compressed air supply |
|
Nozzle diameter |
0.5mm/0.7mm/0.75mm/1.0mm/1.5mm/2.0mm optional 1, standard 1.0 and can be customized according to requirements |
|
Shutdown protection function |
just press the stop button when shutting down, the machine will stop running immediately except for the fan, to ensure that the equipment will not burn out due to misoperation (forced shutdown of the fan). |
|
Machine power |
3.5KW /220V |
|
Dimensions |
1250mm (H) × 650mm (L) × 800mm (W) |
Related photos of spray dryer:
Q. Are you a manufacturer or a trading company?
A. We are professional laboratory instrument manufacturers, have their own design team and factory, have mature technical experience, and can guarantee the quality of products and the optimal price.
Q. How is your company's product after-sales service system?
A. The product warranty period is 12 months, we can provide lifetime maintenance. We have professional pre-sales and after-sales departments that can respond to you within 24 hours to resolve any technical issues.
Q. How long is your delivery time? If I want to customize the instrument, how long does it take?
A.1. If the goods are in stock, it is 5-10 days. 2. We can provide customized services for our customers. It usually takes 30-60 days depending on the specifications of the custom instrument.
Q. Our country's power supply and plug are different. How do you solve it?
A. We can supply a transformer and plug according to your local requirements according to the power plug of different countries.
Q. How to pay?
A.T / T, L / C, D / P, etc., it is recommended to use Alibaba Trade Guarantee.
Q. How is the package of goods? Delivery methods?
A.1. Standard export fumigation sign wooden box packaging 2. Express, air, sea shipping according to customer requirements, find the most suitable way.
More questions, please contact customer service
){kind=link}